Metal Roof Leaks

Metal Roof Leaks

Metal Roof Leaks – Corrugated metal roofs are vulnerable to excessive moisture and damage from strong winds. The individual panels are attached to wood or metal trusses with steel nails or screws that can rust and cause leaks. Strong winds can separate the overlapping edges of the panels and allow the roof to leak. Fixing leaks in a corrugated metal roof starts with locating the source of the leaks. From there, the method used to fix a particular leak depends on the cause.

Tips Fixing Metal Roof Leaks

Use a piece of similar-style corrugated roofing to patch holes. Cut the piece large enough to cover the hole and 6 inches of the surrounding roofing each way, using sheet metal cutters. Apply base coat on the underside of the piece and install it on the roof. Cover the patch and surrounding area with glass-membrane fabric and apply a coat of urethane cement over the entire area.

a metal guard to prevent roof leaks on a budget

a metal guard to prevent roof leaks

cheap arrow metal shed roof leaks

best arrow metal shed roof leaks

can a metal roof leak on a budget

can a metal roof leak

cheap corrugated metal roof leaks

best corrugated metal roof leaks

does a metal roof leak on a budget

does a metal roof leak

Carry the tools and brushes to the roof in a tool belt and include a paint-can opener. Open a container of roof cement or base coat on the roof instead or carrying an open container up the ladder.

Consult a professional regarding additional suggestions and methods for fixing leaks in a corrugated metal roof.

Common Causes of Metal Roof Leaks

1. Metal roofing screws

Roofing screws are responsible for the majority of leaks on metal roofs. Metal roofing screws seal water out by compressing a rubber washer at the base of the screw head. When the screw is driven into the metal roofing panel the rubber washer forms a “ gasket” between the roofing panel and the screw head. It sounds simple enough but several things can go wrong like under driving screws, over driving screws, driving screws at the wrong angle and screws that missed the framing member.

Over driven screws: In an attempt to ensure a tight seal between the metal roofing and the screw head many roofing companies will over drive the screw. The unneeded torch breaks the rubber washer and tends to spin it out to the side.

Under driven screws: These are a result of not enough torch on the screw to properly seat the rubber washer to the metal roofing panel. The rubber washer is never compressed and no gasket is formed.

Screws driven at the wrong angle: These don’t allow the rubber washer to sit flat on the metal roofing. Part of the screw is sealed but part is not sealed.

Screws that have missed the metal strut or wood framing below: These have nothing to seal against. These can be hard leaks to find as many times the screw is their but without touching it you wouldn’t know that it didn’t hit anything and didn’t seal.

Even if the screws were installed correctly with the right amount of torch it doesn’t mean that the rubber washer is safe. Hot summers followed by hard cold winters are unkind to the rubber washers. They degrade and lose their seal and it can be very difficult to distinguish which screw is leaking and which is not.

how to fixing a metal roof leak with a tight budget

how to fixing a metal roof leak

cheap metal building roof leaks

best metal building roof leaks

cheap metal roof leaks around chimney

best metal roof leaks around chimney

cheap metal roof leaks around screws

best metal roof leaks around screws

cheap metal roof leaks at peak

best metal roof leaks at peak

2. Stack flashings

Another area very prone to leaks on a metal roof is the area around stack flashings. Stack flashings are the “ boots “ or flashings around pipes that come out of the metal roof. HVAC vents, air vents, and plumbing pipes all have to vent and come through the metal roof. The stack flashing is how the pipe is water proofed. Most stack flashings are rubber or rubberized material that sits flat on the metal roof and forms a seal but also “squeezes” around the pipe to form another seal. The movement in the metal roofing from expansion and contraction is always testing these seals.

The sun also degrades the rubber flashings which last only about half the time of the metal roof. The more caulking, sealant, or tar that is placed behind and around the stack the more they seam to pond water and leak, it ’s a catch 22.

3. Missing sealants

Metal roof sealants that are installed in conjunction with a metal roof rarely last as long as the metal roofing panels do and need to be replaced with regular roof maintenance. Sealants under trims such as metal ridge caps and Z flashings, around roof transitions, counter flashings, reglets, and pitch pans will all need to be “topped off” from time to time as they wear. Use a metal roof sealant specifically made for metal roofing. Other types silicone caulkings may not adhere to the paint on the roofing panel and trims. Metal roofing goes through a daily expansion – contraction cycle and if any sealants are to last they must be able to remain flexible and stretch with metal without breaking their seal.

4. Curb Flashings

HVAC units on Metal Roofs are usually sitting on curbs. Installing metal roof panels is a relatively easy process but it’s the flashing that really test a metal roofers ability. HVAC offer little room for error when fabricating the flashing and keeping a curb dry can be easier said than done. The up hill side of curbs and the two upper corners of the curb flashing are difficult areas especially on lager HVAC units. Water often gets trapped behind the unit and “stands “ behind the flashing which eventually erodes sealants and begins to leak. The more you caulk, seal, or tar the uphill side the more water it will hold. This Catch 22 is difficult to remedy without removing metal roofing panels and starting over.

cheap metal roof leaks at seams

best metal roof leaks at seams

cheap metal roof leaks in valley

best metal roof leaks in valley

cheap metal roof leaks problems

best metal roof leaks problems

5. Seams and over laps


Seams where 2 pieces of metal roofing over lap each other often leak because of a condition called capillary draw. Capillary Draw is when water can actually travel up hill between two tightly joined pieces of metal. Sealant or butyl tape between the two pieces of metal can break the capillary draw but if not used correctly can actually make leaks worse than if none had been used at all.

Preventing Metal Roof Leaks

The best way to prevent future leaks in your metal building is to hire the right contractor to get the job done. A professional, qualified metal building company will know how to properly install a roof. Most leaks are due to improper installation so the construction phase is vitally important for the future of your roof. During this process, your builder will perform the following tasks to ensure a long-lasting roof:

Install sealant at the right locations: in the panel seams, at the location of screw heads, at 4-way panel laps, at eave connections, and at the underside of the roof panels.
Use the proper roof slope in the design: a too shallow slope will allow water to stand on the roof, creating an environment for leaks.
Properly lock and secure the panels: if the panels are not correctly installed, they are more likely to blow away from strong winds.
Install flashing in the right places: around skylights, chimneys, and pipes.
Install the proper metal roof coating: coatings can stop rust from forming and will encourage water and snow to slide off the roof rather than sit around.


Metal Roof Leaks Examples

cheap metal roof leaks ridge cap

best metal roof leaks ridge cap

cheap metal roof leaks screws

best metal roof leaks screws

cheap metal shed roof leaks

best metal shed roof leaks

cheap pole barn metal roof leaks

best pole barn metal roof leaks

cheap repairing a metal roof leak

best repairing a metal roof leak

cheap sealing metal roof leaks

best sealing metal roof leaks

will a metal roof leak on a budget

will a metal roof leak

Incoming search terms:

  • capillary draw on a roof
  • corrugated metal roof leaking from peak
  • capillary draw steel roof
  • flexible roofing panels leaks -solar
  • repair capillary draw in aluminum pan roof

// script google analytics